1999 Ditch Witch JT4020 - SKU #9100-435

Pb132418_midsize Pb132419_midsize Pb132420_midsize Pb132421_midsize Pb132422_midsize Pb132423_midsize Pb132424_midsize Pb132417_midsize Pb132427_midsize Pb132429_midsize Pb132430_midsize Pb132431_midsize Pb132432_midsize Pb132433_midsize Pb132434_midsize Pb132435_midsize Pb132436_midsize Pb132437_midsize Pb132438_midsize Pb132439_midsize Pb132440_midsize Pb132441_midsize Pb132442_midsize
  • Pb132418_thumb
  • Pb132419_thumb
  • Pb132420_thumb
  • Pb132421_thumb
  • Pb132422_thumb
  • Pb132423_thumb
  • Pb132424_thumb
  • Pb132417_thumb
  • Pb132427_thumb
  • Pb132429_thumb
  • Pb132430_thumb
  • Pb132431_thumb
  • Pb132432_thumb
  • Pb132433_thumb
  • Pb132434_thumb
  • Pb132435_thumb
  • Pb132436_thumb
  • Pb132437_thumb
  • Pb132438_thumb
  • Pb132439_thumb
  • Pb132440_thumb
  • Pb132441_thumb
  • Pb132442_thumb
Click The Image to Enlarge
1999 Ditch Witch JT4020
SOLD!
SKU: 9100-435
COMPLETELY REFURBISHED!
(64) Forged 15' drill pipe (960')
(4) 16-piece pipe baskets
NEW EZ connect II transition rod
NEW Beacon housing assembly
Call today to package this drill to fit your needs!
Specifications
Year: 1999
Make: Ditch Witch
Model: JT4020
Hours: 2,240
Pullback: 40,000
Rotation: 5,000
Tell A Friend About This Equipment!

Service Record For SKU #9100-435

The following services and repairs have been performed on SKU #9100-435 by Source: HDD. You can always be confident in the gear you buy from Source: HDD!

- Service complete - changed all filters<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>

- Checked ALL gearboxes - rotation - thrust (2) - track drive (2)<o:p></o:p>

- Serviced mud pump - drain, flush, and refill crankcase - replace valves and packing, inspect liners<o:p></o:p>

- Repaired wiring to mud pump speed sensor<o:p></o:p>

- Install new rubber flap over hydraulic valves<o:p></o:p>

- Repaired hose carrier, replace missing pieces<o:p></o:p>

- Installed new protective wrap on hoses in hose carrier<o:p></o:p>

- Replaced all damaged hoses and hose wrap<o:p></o:p>

- Wash out radiator and oil cooler<o:p></o:p>

- Replaced bad gauges (3)<o:p></o:p>

- Replaced missing stake down auger<o:p></o:p>

- Replaced arm rests<o:p></o:p>

- Replaced water flow meter and weather cover<o:p></o:p>

- Replaced rear rod thread lube applicator<o:p></o:p>

- Repaired seat deck swivel hydraulics<o:p></o:p>

- Disassembled rear wrench and inspect all pieces - install new wear pads and sleeve<o:p></o:p>

- Replaced sub saver<o:p></o:p>

- Disassembled front wrench and inspect all pieces and install new slide<o:p></o:p>

- Replaced rod loader wear pads and bolts<o:p></o:p>

- Replaced main stake down carriage wear pads<o:p></o:p>

- Replaced both rod guide bearings<o:p></o:p>

- Repaired front rod guide bearing support boss<o:p></o:p>

- Replaced rotation gearbox shaft seals, and sliding shaft retaining nuts and washer<o:p></o:p>

- Replaced wear pads on sliding center rod support<o:p></o:p>

- Replaced missing center rod support extension and bolts<o:p></o:p>

- Replaced damaged/defective switches<o:p></o:p>

- Installed new hood rear hand-hold pocket<o:p></o:p>

- Replaced ESID module and related components<o:p></o:p>

- Replaced thrust controller boot<o:p></o:p>

- disassembled mud check valve and inspect internal pieces (installed new winged valve and seat)<o:p></o:p>

- Repaired safety bar and installed<o:p></o:p>

- Repaired front stake down plate and pins<o:p></o:p>

- Replaced missing right side stake down auger quick release hub<o:p></o:p>

- Re-sealed water swivel<o:p></o:p>

- Replaced rotation carriage wear pads<o:p></o:p>

- Replaced left side track drive gearbox shaft seal and fill with fresh gear oil